Microfluidic Array of Externally Fed Electrospray Thrusters for Micro-Propulsion

Metadata Updated: May 2, 2019

The goal of this proposal is to design an electrospray micropropulsion thruster that utilizes a novel propellant transport mechanism. This project is a collaboration with a group of roughly 15 scientists at the Jet Propulsion Laboratory (JPL). If successful, our thruster will be flight tested in space within three years.

Electrospray propulsion is based on a phenomenon whereby a conductive fluid will spontaneously form sharp cones when in the presence of an electric field. These stable protrusions are commonly referred to as Taylor Cones, after the scientist that described their material-independent geometry. Depending on fluid and field conditions, droplets of liquid or individual ions may be emitted from the tip of a Taylor Cone, producing a self-sustaining stream of charged particles. This technology has been applied to printer heads, material synthesis and propulsion.

Electrospray propulsion has been a subject of research for several decades. It is an extremely attractive technology for three main reasons. First, it is highly scalable as the non-volatile liquid propellant used obviates the need for the robust plumbing required by chemical propulsion systems or Hall thrusters. Since emitted particles are accelerated linearly, they require no nozzle to redirect flow, further reducing the thruster's footprint. Secondly, the thrusters are capable of producing very precise thrust resolution due to the small mass of the emitted ions and the fact that the electrospray process is controlled completely electronically. The final benefit is the spectacularly high exhaust velocity that these systems can produce. The exhaust velocity of a chemical propellant is limited by the specific energy release of the chosen chemical reaction but electrosprayed ions can be accelerated to arbitrarily high velocities. Electrospray exhaust velocities can easily surpass those of chemical thrusters by an order of magnitude. Exhaust velocity is proportional to specific impulse, an important thruster characteristic that describes the fuel consumption rate required to produce a given thrust.

The combination of these three attributes; scalability, precision and fuel efficiency, make electrospray thrusters perfectly suited for use on small satellites (<40 kg). These satellites, including those in the well-known CubeSat platform, are opening the door to space research and entrepreneurship to a wide range of organizations. The capabilities of these satellites are, however, limited as there exist few propulsion systems capable of scaling down small enough to fit on, say, a 1U (10x10x10 cm) CubeSat. Self-propelled small satellites would be more versatile than their free-floating counterparts and would be capable of formation flying, making extremely low cost, high-coverage satellite networks possible.

Though Taylor Cones will readily form on a flat fluid surface, it is preferable to localize the emitting area by placing the fluid at the tip of a sharp protrusion. This also decreases the electric potential required to produce emission, as the sharp convex tip will enhance the local electric field. The majority of electrospray propulsion devices achieve this using small, hollow needles. This internal flow presents a limit to scalability, as microscopic needles are prone to clogging and require high pressure to produce the flux required to sustain emission. The aim of this proposal is to design an array of externally-fed electrospray emitters, including the bulk emitter shape and the micropatterned surfaces of both the emitter and the planar substrate on which they are placed. By selectively patterning the surfaces with grooves and channels of yet to be determined geometries, the flow of liquid can be precisely controlled without any active pumping or actuation. This project will require first principle derivation of free surface fluid flow governing equations in model geometries and subsequent numerical modeling.

Access & Use Information

Public: This dataset is intended for public access and use. License: U.S. Government Work

Downloads & Resources


Metadata Created Date August 1, 2018
Metadata Updated Date May 2, 2019

Metadata Source

Harvested from NASA Data.json

Additional Metadata

Resource Type Dataset
Metadata Created Date August 1, 2018
Metadata Updated Date May 2, 2019
Publisher Space Technology Mission Directorate
Unique Identifier TECHPORT_91582
Public Access Level public
Bureau Code 026:00
Metadata Context https://project-open-data.cio.gov/v1.1/schema/catalog.jsonld
Metadata Catalog ID https://data.nasa.gov/data.json
Schema Version https://project-open-data.cio.gov/v1.1/schema
Catalog Describedby https://project-open-data.cio.gov/v1.1/schema/catalog.json
Datagov Dedupe Retained 20190501230127
Harvest Object Id e96f445d-05fb-4dd3-9bd2-61e7c3cd0e0c
Harvest Source Id 39e4ad2a-47ca-4507-8258-852babd0fd99
Harvest Source Title NASA Data.json
Data First Published 2018-09-01
Homepage URL https://techport.nasa.gov/view/91582
License http://www.usa.gov/publicdomain/label/1.0/
Data Last Modified 2018-07-19
Program Code 026:027
Source Datajson Identifier True
Source Hash 2f51e00e48a8898aaec2e6616964a2f58eb5a677
Source Schema Version 1.1

Didn't find what you're looking for? Suggest a dataset here.